Flightdeck Solutions Forum Index Flightdeck Solutions
Technical Support Forum
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

FSUIPC Offsets Sim-Avionics

 
Post new topic   Reply to topic    Flightdeck Solutions Forum Index -> Sim-Avionics Support
View previous topic :: View next topic  
Author Message
GDR



Joined: 26 Sep 2008
Posts: 311
Location: EBBR

PostPosted: Fri May 31, 2019 11:01 am    Post subject: FSUIPC Offsets Sim-Avionics Reply with quote

Hi,

Where can I find the document with the offsets used by Sim-Avionics?
I can't find them in the manual.

Thx.
_________________
Geert.

Full B737-MAX DSTD
ALL FDS
Sim-Avionics V1.964
P3D v4.5
FSUIPC v5.151

What goes up, must eventually come down!
http://www.flightsim737.be
http://www.flightsim737max.be
http://www.flightsim737ng.be
Back to top
View user's profile Send private message Visit poster's website
thomas747400



Joined: 14 Feb 2016
Posts: 99
Location: Perth, Western Australia

PostPosted: Fri May 31, 2019 6:25 pm    Post subject: Reply with quote

Hi Geert,

FSUIPC offsets can be freely assigned in the server utility > "FSUIPC I/O Interface" tab. There are offset examples under this tab and there is some info in the user manual starting on page 49.

Examples use offsets starting at 5300.
The FSUIPC User Guide states that you can also freely use offsets 66C0 - 66FF.

Hope this helps!

Thomas
Back to top
View user's profile Send private message
GDR



Joined: 26 Sep 2008
Posts: 311
Location: EBBR

PostPosted: Sat Jun 01, 2019 1:06 am    Post subject: Reply with quote

Hi Thomas,

Thanks for the info.
Though, I'm looking to what offsets are used by Sim-avionics itself.
I have a TQ and need to for example configure the engine start levers, toga, reverse, etc... The TQ has 2 cards a joystick and one SIOC (motors). The SIOC card is controlled by programming the logic. I have written the logic as per real aircraft. Though, I need to set some offsets so it tells sim-avionics what state they are in.

An example is T1_lever is 53E0, T2_lever is 53E2 …

Is there a list of what has what offset. A bit like the FSUIPC list like:
&53E0 length 2 Throttle Lever 1
&53E2 length 2 Throttle Lever 2
...

but then for sim-a specifically.

Thx.
_________________
Geert.

Full B737-MAX DSTD
ALL FDS
Sim-Avionics V1.964
P3D v4.5
FSUIPC v5.151

What goes up, must eventually come down!
http://www.flightsim737.be
http://www.flightsim737max.be
http://www.flightsim737ng.be
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic    Flightdeck Solutions Forum Index -> Sim-Avionics Support All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group